A Collaborative National Center for Fusion & Plasma Research
Press Releases

PPPL delivers a plasma source that will enable high-power beam pulses in a new Berkeley Lab accelerator

Plainsboro, New Jersey — Scientists at the U.S. Department of Energy’s Princeton Plasma Physics Laboratory (PPPL) have designed and delivered a crucial component for a device that can heat a spot of foil to 30,000 degrees Centigrade in less than a billionth of a second. The part will complete a linear accelerator that researchers at the E.O. Lawrence Berkeley National Laboratory are using to create a superheated state called “warm dense matter.”

Researchers are eager to study this substance, which is rarely seen on Earth but common throughout the universe. Warm dense matter can be found in the molten core of giant planets like Jupiter, and in the preliminary stages of fusion, a process that powers the sun and stars. Such matter intrigues physicists studying the cosmos and scientists including those at PPPL who are seeking to harness fusion to produce electric power.

For PPPL physicist Erik Gilson, the plasma source he designed for the accelerator marks the third generation of components that he has created for Berkeley Lab projects that are part of the Heavy Ion Fusion Science Virtual National Laboratory, a joint venture of PPPL, Berkeley Lab, and Lawrence Livermore National Laboratory. Gilson’s latest device upgrades previous versions while retaining the core—modules made from 1.6-inch-long rings of barium titanate ceramic. The material produces a swarm of ions and electrons at its surface when a high-voltage is applied to it.

A bit of mystery surrounds where these ions come from. “The mechanism isn’t completely understood,” Gilson said. “It could be absorbed gas on the surface of the modules. But whatever fuel you have is what you brought with you when the parts were installed.”

The 10-meter-long accelerator, known as the Neutralized Drift Compression Experiment-II (NDCX-II), is expected to begin full-scale operation this fall. The device will send a beam of charged lithium particles — or ions — through a series of electromagnetic induction cells that will accelerate and compress the beam, turning it from a javelin-like projectile into one that resembles a tiny comet. The highly compressed beam will heat a target made of a custom-designed foil, producing the warm dense matter that instruments can analyze in the instant before the target vaporizes.

The target material is not like kitchen foil. It measures four one-hundredths of an inch in diameter and is less than a micron thick, making it more than 10 times as thin as the foil that might be used to wrap warm leftovers. It can be made from many materials including gold, tungsten, carbon, or even a metallic foam.

Without the PPPL-designed device, the intense NDCX-II beam would rapidly expand into the beam tube walls before reaching the target. The copper-clad, 43-inch cylinder the size of a hand telescope will create an electrically charged plasma to fill the penultimate stage of the accelerator called the drift line. Negatively charged electrons in the plasma will neutralize the positively charged ion beam after it leaves the accelerator and zips through the drift line on its way to the target chamber. This neutralization is needed to keep the beam from dispersing, since particles with the same charge would repel one another.

Gilson’s device improves upon the plasma source he designed for the previous Berkeley Lab accelerator, the NDCX-I. The biggest change involved connecting a separate 10,000-volt electric power supply to each barium titanate module. This enables researchers to regulate power all along the device and deliver added power to modules that might need it. By contrast, the NDCX-I plasma source connected four or five modules to a single power supply and was unable to regulate the power to individual modules.

The new device rounds out a particle accelerator that has hundreds of times more heating power than the NDCX-I, which was operated by scientists in the mid-2000s. The NDCX-II will compress bunches of about 200 billion lithium ions so rapidly that the tail of the beam will overtake the head in the drift line, condensing the beam to deliver the maximum heating punch. “What makes NDCX-II unique is the beam’s charged-particle density,” said Joe Kwan, Berkeley Lab project manager for the new accelerator.

Construction of the NDCX-II began in 2009 with $11 million from the American Recovery and Reinvestment Act, the stimulus program that Congress passed that year. Experiments on the accelerator will complement research under way at the National Ignition Facility (NIF), part of the Lawrence Livermore National Laboratory. Scientists at NIF are seeking to produce fusion by imploding hydrogen fuel capsules with the world’s most powerful laser beams in a process called inertial confinement. At the same time, Berkeley Lab researchers have been studying ion beams for the possible production of fusion through the same process.

PPPL is funded by the U.S. Department of Energy’s Office of Science and managed by Princeton University. Its research mission is to advance the coupled fields of fusion energy and plasma physics. Fusion is the process that powers the sun and the stars. In the interior of stars, matter is converted into energy by the fusion, or joining, of the nuclei of light atoms to form heavier elements. At PPPL, physicists use a magnetic field to confine plasma. Scientists hope eventually to use fusion energy for the generation of electricity.

U.S. Department of Energy
Princeton Plasma Physics Laboratory is a U.S. Department of Energy national laboratory managed by Princeton University.

Website suggestions and feedback

Google+ · Pinterest · Instagram · Flipboard

PPPL is ISO-14001 certified

Princeton University Institutional Compliance Program

Privacy Policy · Sign In (for staff)

© 2018 Princeton Plasma Physics Laboratory. All rights reserved.

Princeton University
Princeton Plasma Physics Laboratory
P.O. Box 451
Princeton, NJ 08543-0451
GPS: 100 Stellarator Road
Princeton, NJ, 08540
(609) 243-2000